(301) 939-0009Kitchen & bath showroom · Trade desk for builders, designers & homeowners

H&C Kitchen & Bath
Countertops

Kitchen Backsplash Installation Cost: Tile, Slab and Labor

A kitchen backsplash costs $15 to $60 per square foot installed in tile and $60 to $150 in a quartz slab. Material vs labor, line by line, for a 30 square foot wall.

HK H&C Kitchen & Bath Design Team · Showroom Design Center
Published Nov 11, 2026 · 6 min read
White handmade tile backsplash above a quartz countertop and navy lower cabinets

Kitchen backsplash installation costs $15 to $60 per square foot for tile and $60 to $150 for a quartz slab, material and labor included. A typical backsplash is about 30 square feet, so most tile jobs run $450 to $1,800 and a full-height slab $1,800 to $4,500. On a standard tile backsplash, labor is more than half of the bill.

A backsplash is a small surface with a lot of work in it. Every outlet, window return, cabinet end and range hood is a cut, and the wall behind it is rarely flat. That is why the tile you choose often matters less to the total than how it is laid. H&C Kitchen & Bath is a Derwood showroom where backsplash tile and countertop slabs are chosen side by side, and our sister company H&C Construction installs them, so these numbers come from both the sample table and the job site.

Backsplash cost per square foot, by material

Material Material only, per sq ft Installed, per sq ft 30 sq ft backsplash
Ceramic subway tile $2 to $8 $15 to $30 $450 to $900
Porcelain tile $4 to $12 $18 to $35 $540 to $1,050
Glass or mosaic sheets $10 to $30 $30 to $55 $900 to $1,650
Natural stone or handmade tile $15 to $35 $35 to $60 $1,050 to $1,800
Quartz slab, full height Priced like the countertop $60 to $150 $1,800 to $4,500

The installed figures assume a sound, flat wall and a standard layout. Removing an old backsplash, moving outlets and edge trim come on top, as listed further down. On a wall that never sees foot traffic, ceramic performs as well as porcelain for less money, as our porcelain vs ceramic tile guide explains.

To estimate your own area, measure each wall section between the countertop and the bottom of the wall cabinets, usually 18 inches, and multiply by its length. Add the area behind the range up to the hood, which is often the largest single piece. Most kitchens land between 25 and 35 square feet.

Material vs labor on a typical tile backsplash

Here is how a 30 square foot porcelain backsplash breaks down, set in a simple offset pattern on a wall that is ready for tile.

Partly installed subway tile backsplash with spacers and a notched trowel
Line item Type Cost
Porcelain tile, 33 sq ft with overage Material $150 to $400
Thinset, grout, spacers and caulk Material $50 to $80
Layout and cuts around outlets and windows Labor $120 to $200
Setting, grouting and cleanup Labor $220 to $370
Total Material and labor $540 to $1,050

Labor comes to $340 to $570, roughly 55 to 65 percent of the job, or about $11 to $19 per square foot. That ratio is close to a bathroom wall, and for the same reason: a small area with a high number of cuts. Our bathroom tile cost guide shows the same pattern on a larger scale.

What moves the labor price

The tile price is easy to compare in a showroom. The labor price moves with decisions that look small on a sample board:

  • Pattern. Herringbone, chevron and vertical stacks take longer to lay out and cut than a simple offset. Expect 20 to 40 percent more labor.
  • Tile size. Small mosaics on mesh sheets go up quickly but take more grout and cleanup. Large-format tile has fewer joints but needs a flat wall, because any bow in old drywall shows.
  • Handmade tile. Zellige and other handmade tiles vary in thickness and edge, so they are set more slowly and often need sealing.
  • Cuts and edges. Every outlet, switch, window return and open end adds time. Exposed edges need a finished trim tile or a metal profile, typically $5 to $15 per linear foot installed.
  • Minimum charges. Many tile setters have a minimum of $400 to $600, so a small coffee bar backsplash costs more per foot than a full kitchen.

Slab backsplashes: 4 inch splash or full height

A slab backsplash is cut from the same quartz or stone as the countertop and priced per square foot like it. The simplest version is a 4 inch splash along the walls, which uses very little material and is often cut from the countertop slab’s offcuts. A full-height slab, running from the countertop to the wall cabinets or the ceiling, is a bigger decision.

Full-height veined quartz slab backsplash behind a cooktop

A full-height slab has no grout lines to clean and lets the veining continue up the wall, which is why it is so popular behind ranges. The cost depends almost entirely on the stone: an entry quartz costs about what the most expensive handmade tile does, and a designer quartz can pass $4,000 on a 30 square foot wall. Each outlet becomes a cutout, and a second slab may be needed if the countertop layout already uses most of the first. Our quartz countertops cost guide shows where each quartz tier lands.

Extras that are not in the per-foot price

  • Removing an old tile backsplash: $3 to $8 per square foot, about $100 to $250 for 30 square feet, plus drywall repair, often $100 to $300, because tile set on drywall usually tears the paper face off with it.
  • Moving or adding outlets: electrician work, typically $150 to $300 per box. Box extenders for the new tile thickness are a small material cost.
  • Under-cabinet lighting: far easier and cheaper to wire before the tile goes up than after.
  • Sealing: natural stone, handmade tile and cement-based grout need sealing, usually $50 to $150.

The Maryland factor

Tile labor in the DC metro runs 15 to 25 percent above national averages, and the ranges above reflect Montgomery County pricing. Plaster walls in older homes are often out of flat and may need a skim coat before tile. Timing matters too: the backsplash goes in after the countertops are installed, because the tile sits on the stone, and it takes two to four days including grout and cure.

Frequently asked questions

How much does it cost to install a kitchen backsplash?

Most tile backsplashes cost $15 to $60 per square foot installed, so a typical 30 square foot backsplash runs $450 to $1,800. A full-height quartz slab costs $60 to $150 per square foot, or $1,800 to $4,500 for the same wall.

How much is labor to install backsplash tile?

Labor for a standard tile backsplash runs about $10 to $20 per square foot, or roughly $340 to $570 for 30 square feet in a simple pattern. Herringbone, chevron and handmade tile add 20 to 40 percent.

How many square feet is a typical kitchen backsplash?

Most kitchens have 25 to 35 square feet of backsplash. Measure each wall section between the countertop and the wall cabinets, usually 18 inches tall, and add the area behind the range up to the hood.

Is a full-height slab backsplash worth it?

It is worth it behind a range, or anywhere you want continuous veining and no grout to clean. It costs more than most tile and sometimes needs a second slab, so price it once the countertop layout is drawn.

Can you install a new backsplash over old tile?

Sometimes, if the old tile is flat and firmly bonded and the added thickness will not leave outlets and trim looking recessed. In most kitchens, removing it gives a cleaner result for about $100 to $250 more, plus any drywall repair.

Choosing a backsplash? Bring a countertop sample or a photo to our Derwood showroom and we will pull tile and slab options that work with it, so you can compare a $20 and a $50 per foot backsplash next to your stone before you commit. Call (301) 939-0009 or book a showroom visit.

HK
Written by

H&C Kitchen & Bath Design Team

The H&C Kitchen & Bath design team helps homeowners and trade pros across the DMV plan kitchens and baths, from cabinets and countertops to tile and flooring, at our Derwood, MD showroom.

Ready to plan yours?

See the slabs in person at our showroom

Book a free showroom visit and compare your options in person under real lighting.

Book Showroom Visit →